Thank you for purchasing Prido dash camera

Thank you for purchasing Prido dash camera.

This user manual contains technical specifications, safety, installation and operating instructions. Read carefully all the instructions and warnings in the manual before initial use.

Installing the memory card

The camera requires a microSD™ or microSDHC memory card up to 128GB with a speed rating of class 10 or higher and FAT32 formatting. If the card is incompatible, the device may not read it.

Please insert memory card into the slot as shown in the illustration (1.1) hold the card by the edges and gently insert it until it clicks. To remove a card press it to release and pull it out. Turn the device off before removing the card.

Prido X6 Instrukcja obsługi

Installation of front (mirror) and rear camera

Connect the charger to your device using the USB connector, then plug the other end into the cigarette lighter socket. Connect the rear camera to the front camera (see Figure 1.1 for a connection diagram).

CAUTION: The rear camera should be connected only when the device is switched off. Connecting the camera to the DVR when it is switched on may damage the plug and cause image display interference.

Mount the rear camera at the back of the car and route the cable so that it does not obstruct your view or impede driving. In most cars, the best solution is to route the cable under the gaskets located along the top edge of the doors or run it under the headliner.

See Figures 1.2 and 1.3 for suggestions on how to route the cable.

Prido X6 Instrukcja obsługi

Suggested rear camera mounting options

Before installing the rear camera, verify that the camera cable length is appropriate for the installation.

The rear camera can be mounted like a classic reversing camera by leading it outside the vehicle through the tailgate and attaching it with screws to the registration frame or directly to the tailgate. Depending on the car model, in order to carry out this operation it will be necessary to drill additional holes in the tailgate or use the technological holes left by the car manufacturer.

The camera can also be mounted on the rear window. For this purpose we suggest using 2 neodymium magnets. A schematic of this mounting solution is shown in Fig. 1.4. Neodymium magnets are not included in the kit and must be purchased separately.

Prido X6 Instrukcja obsługi

After installing both cameras, make sure the cigarette lighter socket is powered. Start the camera and use the view switch button (Figure 1.5, button number 13) to check, whether both cameras work properly.

The image is adjusted manually (by manually adjusting the camera lens angle) and electronically (using the arrow buttons numbered 16 and 18 in Figure 1.5).

If both cameras have been connected correctly, they will record the video simultaneously. The recorded files will be stored in separate folders on the memory card inserted in the unit.

Reversing camera installation

The rear camera included in the kit can also be used as a reversing camera.

To do this, use the included mounting kit to connect the camera to the reversing light harness. The red cable of the mounting kit should be connected to the car’s reverse light.

We do not recommend that you perform this operation yourself, if you do not have the appropriate knowledge of car electrics. We recommend that the reversing camera be installed only by specialists. When the rear camera is connected to the reverse lights, the reversing camera function will automatically activate when the driver puts the car in reverse gear.


When the reversing camera is properly mounted, the default screen displayed on the unit’s screen after starting will be the rear camera view.

To change the view, use the view toggle button (Figure 1.5, button number 13).

Button functions

Prido X6 Instrukcja obsługi

1. Length of current recording
2. Adjust screen brightness
3. Night mode
5. Parking mode activated
6. Overload sensor (G-Sensor)
7. MicroSD card
8. Battery charging indicator
9. Start/stop recording
10. Take a picture
11. Record/do not record sound
12. Lock/Unlock
13. Switching the view (front/rear)
14. View saved recordings
15. Settings
16. View adjustment (move up)
17. LDWS calibration
18. View adjustment (move down)

Playback of saved recordings

Prido X6 Instrukcja obsługi

1. Back
2. Front camera recordings
3. Rear camera recordings
4. Protected front camera recordings
5. Protected rear camera recordings
6. Photos
7. Protect / Unprotect video recording
8. Delete

To finish viewing your saved recordings, click the back button until you reach the main screen of your device. To select the recording you want to play, tap it with your finger.

Playback screen description

1. Protect/Unprotect video
2. Previous recording
3. Rewind
4. Play/Pause
5. Fast forward
6. Next recording
7. Delete

Description of device functions

Video resolution: Set the video resolution at which the front camera will record
Loop recording: Allows you to set the length of the loop recording.
Night mode: Activating the night mode improves the quality of videos recorded at night and in low light conditions.
Exposure: Allows you to set the exposure (brightness) of the image.
Frequency: Allows you to select the playback frequency.
Rear camera: Turn the rear camera on/off.
Time settings: Allows you to set the appropriate date/time.
Time stamp: Allows you to show/hide the date and time stamp appearing on the right side of the screen.
Format memory card: Causes the data on the memory card to be removed. Factory settings: Restores the device to the default (factory) settings.
Software version: Displays information about the current software version of the device.
Memory card information: Displays current information on the available storage space on the memory card.
ADAS: Allows you to calibrate the LOWS (lane keep assist) and FCWS (collision warning system).
Automatic screen brightness: Allows automatic adjustment of screen brightness depending on the amount of light inside the car.
G-Sensor sensitivity: Allows you to set the sensitivity of the overload sensor.
Parking mode: Enable/disable parking mode.
Screen saver: Allows you to enable/disable the screensaver and set the time after which it should appear.
Language: Allows you to select the device language.
Volume: Allows you to adjust the volume of the device’s buttons or to mute them completely.

Safety and product informations

If these guidelines are not followed, may present a risk of damage to the device.

Do not operate the device outside of the following temperature range: from -20° to 55°C and to sudden and severe temperature changes. In the event of moisture condensation, allow the device to dry out completely before use.

Do not leave the device exposed to a direct sunlight for extended time period.

Use a soft, lint free material to clean your device.

Use only the car charger included in device package.

Battery Warnings

This device contains a non-replaceable lithium-ion battery.

The battery may present a risk of damage to the device, fire or chemical burn. To avoid it do not disassemble, remanufacture, puncture, modify, or damage the device or batteries.

Do not immerse or expose the device or batteries to water, other liquids or fire.

Limitted Warranty

International warranty periods vary subject to local laws and the policies of the authorized importer or distributor for the geographic area where the purchase was made.

This limitted warranty contains that Prido products are warranted to be free from defects in materials or workmanship for two years from the date of purchase.

This limitted warranty contains that Prido products are warranted to be free from defects in materials or workmanship for two years from the date of purchase.

Within two years from the date of purchase, Prido may, at its own discretion, replace any type of device components that will break down during normal use. The user of the device will not be charged with the costs of these components, at the expense of their replacement and at the expense of transporting the device for repair purposes.

This Limited Warranty does not apply to:

■ Cosmetic damage, such as scratches, nicks and dents.
■ Consumable parts, such as batteries, unless product damage has occurred due to a defect in materials or workmanship.
■ Damage to a product that has been connected to power and/or data cables that are not supplied by Prido.
■ Damage caused by service performed by anyone who is not an authorized service provider of Prido.
■ Damage to a product that has been modified or altered without the written permission of Prido.
■ Damage caused by accident, misuse, abuse, flood, water, tire or other acts of nature or external causes.

In addition, Prido reserves the right to refuse warranty claims against products or services that are obtained and/or used in contravention of the laws of any country. If you seek warranty service you should contact Prido Authorized service facility. After contacting it you will gain all informations needed to start your warranty service.

You can contact a Prido Authorized service facility via website or by sending an e-mail at

If during the warranty period you submit a claim for warranty service in accordance with this Limited Warranty, then Prido will, at its option: repair the device, replace the device with a new device or exchange the device for a full refund of your purchase price.

If Prido delivers a repaired device to the customer or replace the device with a new one, the warranty period will commence on the date of delivery of the repaired or replaced product to the customer’s hands and will continue until the warranty period has expired. In other cases, the warranty of the device will be extended by the time when the user could not use the device due to its defect covered by the warranty.

Before seeking warranty service, please access and review the online help resources available on website. If your device is still not functioning properly after making use of these resources, contact a Prido Authorized service facility.

If you seek warranty service outside of the original country of purchase, Prido require you to ship your product to a Prido Authorized service facility in Poland, in which case you will be responsible for complying with all applicable import and export laws and regulations and for paying all custom duties, V.A.T., shipping fees and other associated taxes and charges.

In some cases, Prido may be unable to return a repaired or replaced product to the country outside of the original country of purchase due to applicable standards, laws or regulations in that country.

Servicing of all types associated with the Prido devices can provide only Prido or service centers authorized by Prido.

Limitation of liability to commercial and third-party users

Prido does not bear any responsibility for special, indirect, consequential or incidental losses, loss of profits, loss of data, loss of opportunity regardless of whether they are the result of improper use of the device, resulting from the use or inability to use the product or its defects. The limitation does not apply to liability types, the exclusion or limitation of which is impossible by law.

Prido does not guarantee, does not provide and does not declare that during the service or replacement of the device there is no risk associated with the loss of data and information stored on the device. Before sending the device to Prido, remove your memory card from it. If the memory card is not removed, Prido is not responsible for the data stored on the memory card.


All data and information obtained during the warranty process will be stored by Prido in accordance with the Prido privacy policy available at:

Secondary market and online auctions purchases

Products purchased on secondery market (on line auctions included) are not eligible for Prido warranty coverage. Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required.

General warranty conditions

In the event that any of the paragraphs of this warranty is found to be unlawful or unenforceable, it will be excluded from this warranty. The deletion of this paragraph does not affect the legality and feasibility of the remaining paragraphs of this warranty.

Battery warranty

According to this warranty, the battery contained in the Prido product will not have any manufacturing or material defects for six months from the date of purchase. After six months from the date of purchase, complaints related to the work and/or performance of the device battery will not be considered unless they are directly related to the manufacturing or material defect of the device itself.

MicroSD memory cards and warranty

Due to the variety of microSD cards available on the market, their different specifications and years of manufacture, we are not able to ensure that every card available from the official distribution will work flawlessly with any of our devices, even if the card size and speed criteria are satisfied. Prido does not manufacture microSD cards, therefore cards that do not function properly in Prido devices cannot be the basis of a complaint procedure.

If the memory card causes problems in the Prido device (e.g. it cannot be formatted correctly in the device or keeps prompting to be re-formatted) it may be helpful to reformat it to change the file system to FAT32. A detailed description of this operation can be found at:

Many memory card manufacturers stipulate that cards used in loop recording devices, including video recorders, are not covered by the warranty because these types of devices place a significant strain on the card by having to continuously record data. We recommend that you should review the memory card manufacturer’s warranty terms before you purchase the card.

Recommended accessories

The camera has an input connector for the GPS module which extends the functionality of the recorder by displaying the position on the recording and the speed at which the car is moving. GPSM1 module can be purchased at and from authorized partners.

Device software update

All updates to the device approved by the manufacturer will only appear on their official website, Prido is not responsible for damage to the device caused by installation of software downloaded from other sources. To perform a software update, you must:

1. Format the memory card
2. Go to and in the updates section find the latest software for your device and download it to your computer.
3. Copy the file to a formatted memory card
4. Place the memory card with the file in the device
5. NOTE: Make sure that the device is connected to a power source, as discharging the device during the update may damage it.
6. Turn on the device
7. The device update will start automatically.
8. When the update is complete, the device will power down.
9. After turning it on again, you can start using the device.

Manual in PDF format

Do pobrania: Manual in PDF format (multilangual)